-
فیبر توزیع جعبه
-
جعبه توزیع FTTH
-
جعبه توزیع کابل
-
ماژول LSA Plus
-
MDF اصلی توزیع قاب
-
بلوک ترمینال مشترک
-
پنل رک پنل کوه
-
Rj45 Keystone Jack
-
مدیر کابل افقی
-
فیبر کابل شبکه
-
110 ترمینال بلوک
-
قاب توزیع نوری ODF
-
فیبر نوری سیم کشی
-
فیبر نوری اتصال انشعاب
-
بلوک ترمینال IDC
-
ابزار شبکه پانچ پایین
-
لوازم جانبی فیبر نوری
-
آندریاس ساندویکتولید کننده بسیار باتجربه!
-
کریستوبر گومزیک تولید کننده معتبر، قابل اطمینان و با تجربه شما می توانید بر روی آن حساب کنید
-
Ilker Erimezآنها راه حل های کامل مخابرات را ارائه دادند.
-
احمد عبداللهاتصال دهنده های picabond AMP TYCO مورد استفاده برای ایران telecom عالی کار می کند، مشتری ما با کیفیت بسیار راضی است.
DIN Rack Install Subscriber Terminal Block VX module With / Without Protection
برای نمونه و کوپن رایگان با من تماس بگیرید.
واتساپ:0086 18588475571
ویچت: 0086 18588475571
اسکایپ: sales10@aixton.com
اگر نگرانی دارید، ما به صورت آنلاین 24 ساعته راهنمایی می کنیم.
xname | VX module | Environment condition | 5-40 degree Celsius ,Relative humidity <85% (+30 degree Celsius),Atmospheric pressure, 70-106KPa |
---|---|---|---|
plate | silver 20-40uinch | pulling-out force | not less than 25N |
standard | GB/T 5169.7-1985 | material | pc |
install | DIN rack | Protective | GDT |
برجسته | ,,telecom distribution box |
Applications and feature:
- STB is a high reliability connection module, designed to withstand all existing climates.
- Watertight by design, it provides the best service for the following applications:
- Interface boxes UG/Aerial/Networks
- Distribution points
-Customer termination devices
- Fits on DIN 35 rails
- Very compact, overall dimensions allow to replace existing won protected solution by a high reliability solution.
- No special tool required, only by a standard screw driver.
Range of the section: | diameter 0,4… 1,2 mm |
Diameter on the isolation: | it is maximal 5 mm |
The current-response characteristics: | 20 A(10 A on each conductor) during not less than 10 min, without the deformation of the module |
Insulation resistance | |
“Dry” atmosphere: | > 10 12 Ohm |
“Moist” atmosphere (standard ASTM Of d618, procedure F): | > 10 12 Om |
Salt fog: (standard ASTM Of b117) | > 10 10 Ohm |
Immersion beside the water: (15 days before 3% solution Of naCI) | > 10 10 0m |
The contact resistance | |
R of material + R of the contact cross connection + by R of the contact connection of the wires | < 10 m |
Increase in the contact resistance | |
After climatic testings: | <2,5 m |
After 50 connections - turning offs: | <2,5 m |
Dielectric strength: | >3 kV of direct current during 1 minute |
Mechanical characteristics
Screw of the connection of the pair of the distributive wire: | Special alloy Of zamac, [passivirovannyy], with the paint and varnish coat |
Housing of the unit of the connection | Transparent polycarbonate |
the distributive wire: Housing: | Polycarbonate, glass-reinforced, resistance to fire “VO” |
Fitted contacts: | Tinplated phosphor bronze |
Contacts of the grounding: | Alloy Cu - Zn - Ni - Ag |
Contacts of the connection: | Tinplated solid bronze |
Sealing material before the lower part: | The epoxy resin |
Sealing material before the upper cable part: | Silicon compound |
Cover of the pair of the distributive wire: | Polycarbonate |
Housing of the insertable module: | Polycarbonate, glass-reinforced, resistance to fire “VO” |
Sealing material of the insertable module: | Gel |
The ring gasket: | Elastomer EPDM |
Spring: | the stainless steel |
Cable laying is the distributive wire: | Thermoplastic rubber |